- 您现在的位置：买卖IC网 > Sheet目录874 > Q48T30033-NAAC (Power-One)DC/DC QTR BRICK 100W 3.3V T/H
Q48T30033 DC-DC Converter Data Sheet
36-75 VDC Input; 3.3 VDC @ 30A Output
Q Family
When using remote sense, the output voltage at the con-
verter can be increased by as much as 10% above the
nominal rating in order to maintain the required voltage
across the load. Therefore, the designer must, if necessary,
decrease the maximum current (originally obtained from the
derating curves) by the same percentage to ensure the con-
Vin
Vin (+)
ON/OFF
TM
Converter
(Top View)
Vout (+)
SENSE (+)
TRIM
SENSE (-)
R T-INCR
Rload
verter’s actual output power remains at or below the maxi-
mum allowable output power.
Vin (-)
Vout (-)
Output Voltage Adjust /TRIM (Pin 6)
The converter’s output voltage can be adjusted up 10% or
down 20% relative to the rated output voltage by the addition
of an externally connected resistor. Trim up to 10% is guar-
anteed only at Vin ≥ 40 V, and it is marginal (8% to 10%) at
Vin = 36 V.
The TRIM pin should be left open if trimming is not being
used. To minimize noise pickup, a 0.1 μ F capacitor is con-
nected internally between the TRIM and SENSE(-) pins.
To increase the output voltage, refer to Fig. 4. A trim resistor,
Fig. 4: Configuration for increasing output voltage .
where,
R T ? DECR = Required value of trim-down resistor [k ? ]
and ? is as defined above.
Note: The above equations for calculation of trim resistor
values match those typically used in conventional industry-
standard quarter bricks.
Q Family
R T-INCR , should be connected between the TRIM (Pin 6) and
SENSE(+) (Pin 7), with a value of:
Vin (+)
TM
Converter
(Top View)
Vout (+)
SENSE (+)
R T ? INCR =
5.11(100 + ? )V O ? NOM ? 626
1.225 ?
? 10.22 [k ? ]
Vin
ON/OFF
Vin (-)
TRIM
SENSE (-)
Vout (-)
R T-DECR
Rload
where,
R T ? INCR = Required value of trim-up resistor k ? ]
V O ? NOM = Nominal value of output voltage [V]
Fig. 5: Configuration for decreasing output voltage.
? =
(V O - REQ ? V O - NOM )
V O - NOM
X 100 [%]
Trimming/sensing beyond 110% of the rated output voltage
is not an acceptable design practice, as this condition could
cause unwanted triggering of the output over-voltage protec-
tion (OVP) circuit. The designer should ensure that the dif-
V O ? REQ = Desired (trimmed) output voltage [V].
When trimming up, care must be taken not to exceed the
converter‘s maximum allowable output power. See previous
section for a complete discussion of this requirement.
To decrease the output voltage (Fig. 5), a trim resistor,
R T-DECR , should be connected between the TRIM (Pin 6) and
SENSE(-) (Pin 5), with a value of:
ference between the voltages across the converter’s output
pins and its sense pins does not exceed 0.33 V, or:
[V OUT ( + ) ? V OUT ( ? )] ? [V SENSE ( + ) ? V SENSE ( ? )] ≤ 0.33 [V]
This equation is applicable for any condition of output sens-
ing and/or output trim.
R T ? DECR =
511
?
? 10.22 [k ? ]
MAY 09, 2003 revised to NOV 20, 2006
Page 6 of 14
www.power-one.com
发布紧急采购，3分钟左右您将得到回复。
相关PDF资料
QAK2J335KTP
CAP FILM 3.3UF 630VDC AXIAL
QD48S018033-NS00
DC/DC QTR BRICK 77W 1.8/3.3V
QD48T012025-NCB0
DC/DC QTR BRICK DL 1.2/2.5V T/H
QD48T018025-NBB0
CONV DC-DC 37.5W 2.5/1.8V DUAL
QD48T025033-NBB0
CONV DC-DC 48V IN 3.3/2.5V DUAL
QD48T033050-PBC0
DC/DC QTR BRICK DL 3.3V/5V T/H
QL48T30012-NBA0
DC/DC QTR BRICK 36W 1.2V OUT T/H
QLS08ZH-NT
DC/DC QTR BRICK 96W 12V OUT
相关代理商/技术参数
Q48T30033-NAACG
功能描述:DC/DC转换器 RoHS:否 制造商:Murata 产品: 输出功率: 输入电压范围:3.6 V to 5.5 V 输入电压（标称）: 输出端数量:1 输出电压（通道 1）:3.3 V 输出电流（通道 1）:600 mA 输出电压（通道 2）: 输出电流（通道 2）: 安装风格:SMD/SMT 封装 / 箱体尺寸:
Q48T30033-NAAP
制造商:Power-One 功能描述:DC/DC PS SGL-OUT 3.3V 30A - Bulk
Q48T30033-NAAPG
制造商:Power-One 功能描述:DC/DC PS SGL-OUT 3.3V 30A - Bulk
Q48T30033-NAB0G
制造商:Power-One 功能描述:DC/DC PS SGL-OUT 3.3V 30A - Bulk
Q48T30033-NABP
制造商:Power-One 功能描述:DC/DC PS SGL-OUT 3.3V 30A - Bulk
Q48T30033-NABPG
制造商:Power-One 功能描述:DC/DC PS SGL-OUT 3.3V 30A - Bulk
Q48T30033-NAC0
制造商:Power-One 功能描述:DC/DC PS SGL-OUT 3.3V 30A - Bulk
Q48T30033-NAC0G
制造商:Power-One 功能描述:DC/DC PS SGL-OUT 3.3V 30A - Bulk